How to do Aircon Servicing


Keep your air-conditioner (AC) maintained and you’ll not just save cash on energy, however, you’ll conjointly extend its period, saving cash on expensive early replacement. Dave Moody, HVAC professional from Service

Experts, says, “An AC wants regular attention to make sure it’s operational at the best potency.” The best time to use the following pointers is simply before every cooling season begins.

Your Heating, Ventilating, and Air-Conditioning system (HVAC&) can include either a chamber and AC or a setup, that heats and cools. Each variety can have an internal unit (evaporator and blower) and associate exterior unit (condenser coil and compressor). These directions apply to a whole-home air-conditioning or setup unit.

Here are the following steps :

#STEP 1 :

  • HVAC Unit On/Off Switch
  • Shut Off the power

#STEP 2 :

  • Remove detritus
  • On the outside condenser/compressor, take away the fan cage. employing a screwdriver or wrench, remove the fasteners and raise the cage or fan grill aloof from the highest of the unit. 
  • By hand, or with a wet/dry vacuum, clean leaves and alternative detritus from the inside.

#STEP 3 :

  • Cleaning an HVAC Unit
  • Clean the Fins
  • Remove the outer covers and use the comb attachment on a strong search vacuum to get rid of all outside dirt. 
  • Then, employing a light stream from a hose, spray through the fins from the within & out to remove any designed-up dirt or detritus from between them. 
  • Ne’er uses a pressure washer since the pressure will harm the fins. 
  • If the fins are significantly dirty, use a commercially accessible fin cleansing spray (available reception improvement/ service centres; scan and follow manufacturer directions).

#STEP 4 :

  • Straighten the Fins
  • Since any reduction in air-flow through the fins will cut back potency, rigorously straighten bent fins exploitation with a table knife or commercially accessible fin-straightening tool. 
  • Be gentle so that the conduit embedded within the fins isn’t broken.

#STEP 5 :

  • Clean space around the Unit
  • Once finished with the cleaning, replace the fan cage. Rake back leaves and detritus outside the condenser and take away any cowl once the unit is working.

#STEP 6 :

  • Level the Unit
  • Over time, the pad upon that the condenser unit sits will begin to tip because the soil settles at a lower place. An out-of-level condenser unit will cause the mechanical device to fail early. 
  • Check the condenser for level and use rot-resistant shims to bring it back to level. Service Experts’ Moody adds this exception.

#STEP 7 :

  • Clean the Evaporator Coil
  • Now it’s time to maneuver within. On the within blower/furnace unit, realize the evaporator coil door. 
  • Clean out the drain pan with soap, hot water, and a touch bleach. Then, pour a cup of fifty bleach/50% water down the drain. 
  • To stay the drain clear longer-term, place a commercially accessible drain pan pill within the pan. This can inhibit future algae growth.

#STEP 8 :

  • Clean and obstructed Evaporator Drain
  • On the inside, warm, wet air from your home’s interior is blown through the evaporator coil. The cold coil absorbs heat from the air, cooling it, before the air is circulated into your home. 
  • The humidity within the air condenses on the cool surface of the evaporator coil as liquid water, dripping into a pan below. 
  • From the pan, the water flows into a drain tube that is often routed into a basement floor drain, utility sink, or outdoors.
  • First, realize the drain line wherever it leaves the evaporator coil enclosure. The drain is typically a one-inch PVC pipe (white, grey, or black). Follow it to the tip wherever it drains. 
  • Typically, the road drains outside close to the condenser unit, however, it also can drain into a utility sink or basement floor drain or, within the case of attic units, down an out of doors wall.
  • Once set, use a wet/dry vacuum to clear the drain. It’s best to get rid of the paper filter from the wet/dry vacuum thus as to not ruin the filter. 
  • Hold the hose of the wet/dry vacuum to the tip of the drain line. You’ll use adhesive tape or just hold a rag around the gap. Activate the vacuum for 2-3 minutes then put off. this can clear the drain of any growing biological matter.

#STEP 9 :

  • Change the Blower Filter
  • Locate the filter enclosure on the indoor furnace/AC wherever the massive recent air come back duct enters the unit. 
  • You will like a screwdriver to show the latch to open the door to the filter enclosure. 
  • Remove the old filter and install the new filter, matching the air-flow direction arrows on the filter to the arrows on the unit. 
  • Shut and latch the door.

Be First to Comment

Leave a Reply

Your email address will not be published. Required fields are marked *